Easy Faux Railroad Tie Mantel

 

Faux Railroad Tie Mantel (Create, Paint, Distress, Install)

DIY Fireplace mantel, faux railroad tie

Welcome back.  After showing you my painted fireplace  earlier in the week I promised I would return to show you the DIY faux railroad tie mantel that finishes off my makeover.

It does look a bit like a railroad tie doesn’t it?  Well, it has all the beauty of a railroad tie without the weight and without the creosote.

 

DIY Fireplace Mantel , faux railroad tie

Gather Your Aged Wood

My faux railroad tie is actually made from 3, 2×8’s that I picked up from a local salvage yard.  The one on top has more knots, more splinters and more flaws than the other two and that is why it is perfect for my face board…the board everybody is gonna see.

DIY Fireplace Mantel , faux railroad tie

Measure and cut your three boards.

DIY Fireplace Mantel , faux railroad tie

These screws are just temporary, just holding my boards together while I work on the other holes.

DIY Fireplace Mantel , faux railroad tie

Find a dowel and a drill bit the same size as your dowel.

On the front board of your mantel, drill holes about 1/4 – 1/2 inch deep using a tape measure to evenly space your holes.  These holes will eventually hold the screws that will hold all three pieces of the mantel together.

DIY Fireplace Mantel , faux railroad tie

Glue and Screw Mantel Together

DIY Fireplace Mantel , faux railroad tie

Use wood screws at least 3 inches long to attach the mantel pieces together screwing through the dowel holes you just drilled.

Cut pieces of your dowel to plug up the holes and glue into place.

DIY Fireplace Mantel , faux railroad tie

DIY Fireplace Mantel , faux railroad tie

With any leftover wood, fill in the ends of your mantel and screw into place.

You don’t really have to hide these screws since they will be on the topside and underneath the mantel and they will eventually get a coat of wax/paint.

Sand and Distress your Mantel

DIY Fireplace Mantel , faux railroad tie

Sand off any splinters and any dowels that stick up.

DIY Fireplace Mantel , faux railroad tie

If your front facing board is in need of a little aging here are a few tools you can use.  Dent it with a hammer, prick it with a nail, stick a screwdriver into the wood or just pound it with a meat tenderizer.

Wax and Paint your Mantel

DIY Fireplace Mantel , faux railroad tie

I’ve used this technique before, but to get a nice aged brown/black railroad tie look, use vintage wax and black chalk paint.

Paint on a nice layer of the vintage wax and before it is dry add a few brush strokes of black.  Rub it in and blend with a rag.

DIY Fireplace Mantel , faux railroad tie

Finish the mantel with a coat of clear wax.

Install

DIY Fireplace Mantel , faux railroad tie

This board is exactly the width of my mantel.  Mark the top of the mantel making sure it is level.

DIY Fireplace Mantel , faux railroad tie

The top line is where the top of my mantel will sit.  The bottom line is the width of the top mantel board.

Also mark where all your studs are.

DIY Fireplace Mantel , faux railroad tie-015

Cut a piece of 2×4  long enough to sit inside your mantel.  About every foot screw on  extra pieces of 2×4 bracing short enough so that the entire piece will fit inside the newly built mantel.

Center on your wall and using the stud marks you just made, mark on the 2×4 where bolts will go.

Predrill these holes.

DIY Fireplace Mantel , faux railroad tie

Line up your 2×4 brace with the lower line you made and bolt to the wall going thru all the marked studs.

DIY Fireplace Mantel , faux railroad tie

Get some strong handsome young man (thanks Nathan) to help you slide the mantel over the 2×4’s and use long wood screws to screw in from the top attaching to the 2×4’s.

Sorry no pictures of that, all our hands were busy.

DIY Fireplace mantel, faux railroad tieJust wanted to show you a picture of the finished plugged screw holes.

DIY Fireplace mantel, faux railroad tie

The old mantel had covered the top two rows of bricks but this mantel sits on top of the brick so a simple piece of trim hides the rough edge of the brick.

 

DIY Fireplace mantel, faux railroad tie
DIY Fireplace Mantel , faux railroad tie

DIY Fireplace mantel, faux railroad tie

DIY Fireplace Mantel , faux railroad tie

Before and After Fireplace Makeover

After 25 years of the same old fireplace, I am loving the new fresh look.

While the railroad tie mantel makes a big impact, it’s a fairly easy build.  I hope I’ve inspired you to take it on.

Shared at Salvaged Junk Projects,

Metamorphosis MondayWow us Wednesdays,

Talk of the town,

9 Comments

  • Stacy says:

    That’s looks amazing. Great job.

  • Kimberly says:

    Thanks so much. This new look is great!

  • Colleen says:

    Love love love!

  • Big impact. White and dark contrast.
    Joy

  • Charlee says:

    It turned out amazing! Adds so much character to the room.

    Aloha,

    Charlee

  • wow, this looks like a whole new piece!
    b

  • Shirley says:

    First of all this looks fantastic! I do a lot of research online as I purchased a home four years ago, oh what am I saying, I LIVE for design and crafting so I am always researching..lol! This is one of my research projects as I have a 3 sided fireplace and can’t figure out what to do with it. I love your creativity on this mantel and have to say, this is probably the best faux manel build I’ve ever seen!
    I don’t care much for the way the end looks but that’s a hard one to work with. I LOVE the way you added your wax and paint. It gave just the perfect coloring to look like a RR tie. I also love that you took the time to add the dowel and hide those screws. They look perfect on there and very natural. I will be following more of what you do as from what I’ve seen so far, I ❤️!

Leave a Reply to the cape on the corner Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.